esp32_Adafruit_BME280_Library/Adafruit_BME280.cpp

/*!
 * @file Adafruit_BME280.cpp
 *
 * @mainpage Adafruit BME280 humidity, temperature & pressure sensor
 *
 * @section intro_sec Introduction
 *
 *  Driver for the BME280 humidity, temperature & pressure sensor
 *
 * These sensors use I2C or SPI to communicate, 2 or 4 pins are required
 * to interface.
 *
 * Designed specifically to work with the Adafruit BME280 Breakout
 * ----> http://www.adafruit.com/products/2652
 *
 *  Adafruit invests time and resources providing this open source code,
 *  please support Adafruit and open-source hardware by purchasing
 *  products from Adafruit!
 *
 * @section author Author
 *
 * Written by Kevin "KTOWN" Townsend for Adafruit Industries.
 *
 * @section license License
 *
 * BSD license, all text here must be included in any redistribution.
 * See the LICENSE file for details.
 *
 */

#include "Adafruit_BME280.h"
#include "Arduino.h"
#include <SPI.h>
#include <Wire.h>

/*!
 *  @brief  class constructor
 */
Adafruit_BME280::Adafruit_BME280() : _cs(-1), _mosi(-1), _miso(-1), _sck(-1) {}

/*!
 *   @brief  class constructor if using hardware SPI
 *   @param  cspin the chip select pin to use
 *   @param  *theSPI
 *           optional SPI object
 */
Adafruit_BME280::Adafruit_BME280(int8_t cspin, SPIClass *theSPI) {
  _cs = cspin;
  _mosi = _miso = _sck = -1;
  _spi = theSPI;
}

/*!
 *   @brief  class constructor if using software SPI
 *   @param cspin the chip select pin to use
 *   @param mosipin the MOSI pin to use
 *   @param misopin the MISO pin to use
 *   @param sckpin the SCK pin to use
 */
Adafruit_BME280::Adafruit_BME280(int8_t cspin, int8_t mosipin, int8_t misopin,
                                 int8_t sckpin)
    : _cs(cspin), _mosi(mosipin), _miso(misopin), _sck(sckpin) {}

Adafruit_BME280::~Adafruit_BME280(void) {
  if (temp_sensor) {
    delete temp_sensor;
  }
  if (pressure_sensor) {
    delete pressure_sensor;
  }
  if (humidity_sensor) {
    delete humidity_sensor;
  }
}

/*!
 *   @brief  Initialise sensor with given parameters / settings
 *   @param addr the I2C address the device can be found on
 *   @param theWire the I2C object to use, defaults to &Wire
 *   @returns true on success, false otherwise
 */
bool Adafruit_BME280::begin(uint8_t addr, TwoWire *theWire) {
  bool status = false;
  _i2caddr = addr;
  _wire = theWire;
  status = init();

  return status;
}

/*!
 *   @brief  Initialise sensor with given parameters / settings
 *   @returns true on success, false otherwise
 */
bool Adafruit_BME280::init() {
  // init I2C or SPI sensor interface
  if (_cs == -1) {
    // I2C
    _wire->begin();
  } else {
    digitalWrite(_cs, HIGH);
    pinMode(_cs, OUTPUT);
    if (_sck == -1) {
      // hardware SPI
      _spi->begin();
    } else {
      // software SPI
      pinMode(_sck, OUTPUT);
      pinMode(_mosi, OUTPUT);
      pinMode(_miso, INPUT);
    }
  }

  // check if sensor, i.e. the chip ID is correct
  _sensorID = read8(BME280_REGISTER_CHIPID);
  if (_sensorID != 0x60)
    return false;

  // reset the device using soft-reset
  // this makes sure the IIR is off, etc.
  write8(BME280_REGISTER_SOFTRESET, 0xB6);

  // wait for chip to wake up.
  delay(10);

  // if chip is still reading calibration, delay
  while (isReadingCalibration())
    delay(10);

  readCoefficients(); // read trimming parameters, see DS 4.2.2

  setSampling(); // use defaults

  delay(100);

  return true;
}

/*!
 *   @brief  setup sensor with given parameters / settings
 *
 *   This is simply a overload to the normal begin()-function, so SPI users
 *   don't get confused about the library requiring an address.
 *   @param mode the power mode to use for the sensor
 *   @param tempSampling the temp samping rate to use
 *   @param pressSampling the pressure sampling rate to use
 *   @param humSampling the humidity sampling rate to use
 *   @param filter the filter mode to use
 *   @param duration the standby duration to use
 */
void Adafruit_BME280::setSampling(sensor_mode mode,
                                  sensor_sampling tempSampling,
                                  sensor_sampling pressSampling,
                                  sensor_sampling humSampling,
                                  sensor_filter filter,
                                  standby_duration duration) {
  _measReg.mode = mode;
  _measReg.osrs_t = tempSampling;
  _measReg.osrs_p = pressSampling;

  _humReg.osrs_h = humSampling;
  _configReg.filter = filter;
  _configReg.t_sb = duration;

  // making sure sensor is in sleep mode before setting configuration
  // as it otherwise may be ignored
  write8(BME280_REGISTER_CONTROL, MODE_SLEEP);

  // you must make sure to also set REGISTER_CONTROL after setting the
  // CONTROLHUMID register, otherwise the values won't be applied (see
  // DS 5.4.3)
  write8(BME280_REGISTER_CONTROLHUMID, _humReg.get());
  write8(BME280_REGISTER_CONFIG, _configReg.get());
  write8(BME280_REGISTER_CONTROL, _measReg.get());
}

/*!
 *   @brief  Encapsulate hardware and software SPI transfer into one
 * function
 *   @param x the data byte to transfer
 *   @returns the data byte read from the device
 */
uint8_t Adafruit_BME280::spixfer(uint8_t x) {
  // hardware SPI
  if (_sck == -1)
    return _spi->transfer(x);

  // software SPI
  uint8_t reply = 0;
  for (int i = 7; i >= 0; i--) {
    reply <<= 1;
    digitalWrite(_sck, LOW);
    digitalWrite(_mosi, x & (1 << i));
    digitalWrite(_sck, HIGH);
    if (digitalRead(_miso))
      reply |= 1;
  }
  return reply;
}

/*!
 *   @brief  Writes an 8 bit value over I2C or SPI
 *   @param reg the register address to write to
 *   @param value the value to write to the register
 */
void Adafruit_BME280::write8(byte reg, byte value) {
  if (_cs == -1) {
    _wire->beginTransmission((uint8_t)_i2caddr);
    _wire->write((uint8_t)reg);
    _wire->write((uint8_t)value);
    _wire->endTransmission();
  } else {
    if (_sck == -1)
      _spi->beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
    digitalWrite(_cs, LOW);
    spixfer(reg & ~0x80); // write, bit 7 low
    spixfer(value);
    digitalWrite(_cs, HIGH);
    if (_sck == -1)
      _spi->endTransaction(); // release the SPI bus
  }
}

/*!
 *   @brief  Reads an 8 bit value over I2C or SPI
 *   @param reg the register address to read from
 *   @returns the data byte read from the device
 */
uint8_t Adafruit_BME280::read8(byte reg) {
  uint8_t value;

  if (_cs == -1) {
    _wire->beginTransmission((uint8_t)_i2caddr);
    _wire->write((uint8_t)reg);
    _wire->endTransmission();
    _wire->requestFrom((uint8_t)_i2caddr, (byte)1);
    value = _wire->read();
  } else {
    if (_sck == -1)
      _spi->beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
    digitalWrite(_cs, LOW);
    spixfer(reg | 0x80); // read, bit 7 high
    value = spixfer(0);
    digitalWrite(_cs, HIGH);
    if (_sck == -1)
      _spi->endTransaction(); // release the SPI bus
  }
  return value;
}

/*!
 *   @brief  Reads a 16 bit value over I2C or SPI
 *   @param reg the register address to read from
 *   @returns the 16 bit data value read from the device
 */
uint16_t Adafruit_BME280::read16(byte reg) {
  uint16_t value;

  if (_cs == -1) {
    _wire->beginTransmission((uint8_t)_i2caddr);
    _wire->write((uint8_t)reg);
    _wire->endTransmission();
    _wire->requestFrom((uint8_t)_i2caddr, (byte)2);
    value = (_wire->read() << 8) | _wire->read();
  } else {
    if (_sck == -1)
      _spi->beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
    digitalWrite(_cs, LOW);
    spixfer(reg | 0x80); // read, bit 7 high
    value = (spixfer(0) << 8) | spixfer(0);
    digitalWrite(_cs, HIGH);
    if (_sck == -1)
      _spi->endTransaction(); // release the SPI bus
  }

  return value;
}

/*!
 *   @brief  Reads a signed 16 bit little endian value over I2C or SPI
 *   @param reg the register address to read from
 *   @returns the 16 bit data value read from the device
 */
uint16_t Adafruit_BME280::read16_LE(byte reg) {
  uint16_t temp = read16(reg);
  return (temp >> 8) | (temp << 8);
}

/*!
 *   @brief  Reads a signed 16 bit value over I2C or SPI
 *   @param reg the register address to read from
 *   @returns the 16 bit data value read from the device
 */
int16_t Adafruit_BME280::readS16(byte reg) { return (int16_t)read16(reg); }

/*!
 *   @brief  Reads a signed little endian 16 bit value over I2C or SPI
 *   @param reg the register address to read from
 *   @returns the 16 bit data value read from the device
 */
int16_t Adafruit_BME280::readS16_LE(byte reg) {
  return (int16_t)read16_LE(reg);
}

/*!
 *   @brief  Reads a 24 bit value over I2C
 *   @param reg the register address to read from
 *   @returns the 24 bit data value read from the device
 */
uint32_t Adafruit_BME280::read24(byte reg) {
  uint32_t value;

  if (_cs == -1) {
    _wire->beginTransmission((uint8_t)_i2caddr);
    _wire->write((uint8_t)reg);
    _wire->endTransmission();
    _wire->requestFrom((uint8_t)_i2caddr, (byte)3);

    value = _wire->read();
    value <<= 8;
    value |= _wire->read();
    value <<= 8;
    value |= _wire->read();
  } else {
    if (_sck == -1)
      _spi->beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
    digitalWrite(_cs, LOW);
    spixfer(reg | 0x80); // read, bit 7 high

    value = spixfer(0);
    value <<= 8;
    value |= spixfer(0);
    value <<= 8;
    value |= spixfer(0);

    digitalWrite(_cs, HIGH);
    if (_sck == -1)
      _spi->endTransaction(); // release the SPI bus
  }

  return value;
}

/*!
 *  @brief  Take a new measurement (only possible in forced mode)
 */
void Adafruit_BME280::takeForcedMeasurement() {
  // If we are in forced mode, the BME sensor goes back to sleep after each
  // measurement and we need to set it to forced mode once at this point, so
  // it will take the next measurement and then return to sleep again.
  // In normal mode simply does new measurements periodically.
  if (_measReg.mode == MODE_FORCED) {
    // set to forced mode, i.e. "take next measurement"
    write8(BME280_REGISTER_CONTROL, _measReg.get());
    // wait until measurement has been completed, otherwise we would read
    // the values from the last measurement
    while (read8(BME280_REGISTER_STATUS) & 0x08)
      delay(1);
  }
}

/*!
 *   @brief  Reads the factory-set coefficients
 */
void Adafruit_BME280::readCoefficients(void) {
  _bme280_calib.dig_T1 = read16_LE(BME280_REGISTER_DIG_T1);
  _bme280_calib.dig_T2 = readS16_LE(BME280_REGISTER_DIG_T2);
  _bme280_calib.dig_T3 = readS16_LE(BME280_REGISTER_DIG_T3);

  _bme280_calib.dig_P1 = read16_LE(BME280_REGISTER_DIG_P1);
  _bme280_calib.dig_P2 = readS16_LE(BME280_REGISTER_DIG_P2);
  _bme280_calib.dig_P3 = readS16_LE(BME280_REGISTER_DIG_P3);
  _bme280_calib.dig_P4 = readS16_LE(BME280_REGISTER_DIG_P4);
  _bme280_calib.dig_P5 = readS16_LE(BME280_REGISTER_DIG_P5);
  _bme280_calib.dig_P6 = readS16_LE(BME280_REGISTER_DIG_P6);
  _bme280_calib.dig_P7 = readS16_LE(BME280_REGISTER_DIG_P7);
  _bme280_calib.dig_P8 = readS16_LE(BME280_REGISTER_DIG_P8);
  _bme280_calib.dig_P9 = readS16_LE(BME280_REGISTER_DIG_P9);

  _bme280_calib.dig_H1 = read8(BME280_REGISTER_DIG_H1);
  _bme280_calib.dig_H2 = readS16_LE(BME280_REGISTER_DIG_H2);
  _bme280_calib.dig_H3 = read8(BME280_REGISTER_DIG_H3);
  _bme280_calib.dig_H4 = ((int8_t)read8(BME280_REGISTER_DIG_H4) << 4) |
                         (read8(BME280_REGISTER_DIG_H4 + 1) & 0xF);
  _bme280_calib.dig_H5 = ((int8_t)read8(BME280_REGISTER_DIG_H5 + 1) << 4) |
                         (read8(BME280_REGISTER_DIG_H5) >> 4);
  _bme280_calib.dig_H6 = (int8_t)read8(BME280_REGISTER_DIG_H6);
}

/*!
 *   @brief return true if chip is busy reading cal data
 *   @returns true if reading calibration, false otherwise
 */
bool Adafruit_BME280::isReadingCalibration(void) {
  uint8_t const rStatus = read8(BME280_REGISTER_STATUS);

  return (rStatus & (1 << 0)) != 0;
}

/*!
 *   @brief  Returns the temperature from the sensor
 *   @returns the temperature read from the device
 */
float Adafruit_BME280::readTemperature(void) {
  int32_t var1, var2;

  int32_t adc_T = read24(BME280_REGISTER_TEMPDATA);
  if (adc_T == 0x800000) // value in case temp measurement was disabled
    return NAN;
  adc_T >>= 4;

  var1 = (int32_t)((adc_T / 8) - ((int32_t)_bme280_calib.dig_T1 * 2));
  var1 = (var1 * ((int32_t)_bme280_calib.dig_T2)) / 2048;
  var2 = (int32_t)((adc_T / 16) - ((int32_t)_bme280_calib.dig_T1));
  var2 = (((var2 * var2) / 4096) * ((int32_t)_bme280_calib.dig_T3)) / 16384;

  t_fine = var1 + var2;

  int32_t T = (t_fine * 5 + 128) / 256;

  return (float)T / 100;
}

/*!
 *   @brief  Returns the pressure from the sensor
 *   @returns the pressure value (in Pascal) read from the device
 */
float Adafruit_BME280::readPressure(void) {
  int64_t var1, var2, var3, var4;

  readTemperature(); // must be done first to get t_fine

  int32_t adc_P = read24(BME280_REGISTER_PRESSUREDATA);
  if (adc_P == 0x800000) // value in case pressure measurement was disabled
    return NAN;
  adc_P >>= 4;

  var1 = ((int64_t)t_fine) - 128000;
  var2 = var1 * var1 * (int64_t)_bme280_calib.dig_P6;
  var2 = var2 + ((var1 * (int64_t)_bme280_calib.dig_P5) * 131072);
  var2 = var2 + (((int64_t)_bme280_calib.dig_P4) * 34359738368);
  var1 = ((var1 * var1 * (int64_t)_bme280_calib.dig_P3) / 256) + ((var1 * ((int64_t)_bme280_calib.dig_P2) * 4096));
  var3 = ((int64_t)1) * 140737488355328;
  var1 = (var3 + var1) * ((int64_t)_bme280_calib.dig_P1) / 8589934592;

  if (var1 == 0) {
      return 0; // avoid exception caused by division by zero
  }

  var4 = 1048576 - adc_P;
  var4 = (((var4 * 2147483648) - var2) * 3125) / var1;
  var1 = (((int64_t)_bme280_calib.dig_P9) * (var4 / 8192) * (var4 / 8192)) / 33554432;
  var2 = (((int64_t)_bme280_calib.dig_P8) * var4) / 524288;
  var4 = ((var4 + var1 + var2) / 256) + (((int64_t)_bme280_calib.dig_P7) * 16);

  uint32_t P = (uint32_t)(((var4 / 2) * 100) / 128);

  return (float)P / 256;
}

/*!
 *  @brief  Returns the humidity from the sensor
 *  @returns the humidity value read from the device
 */
float Adafruit_BME280::readHumidity(void) {
  int32_t var1, var2, var3, var4, var5;

  readTemperature(); // must be done first to get t_fine

  int32_t adc_H = read16(BME280_REGISTER_HUMIDDATA);
  if (adc_H == 0x8000) // value in case humidity measurement was disabled
    return NAN;

  var1 = t_fine - ((int32_t)76800);
  var2 = (int32_t)(adc_H * 16384);
  var3 = (int32_t)(((int32_t)_bme280_calib.dig_H4) * 1048576);
  var4 = ((int32_t)_bme280_calib.dig_H5) * var1;
  var5 = (((var2 - var3) - var4) + (int32_t)16384) / 32768;
  var2 = (var1 * ((int32_t)_bme280_calib.dig_H6)) / 1024;
  var3 = (var1 * ((int32_t)_bme280_calib.dig_H3)) / 2048;
  var4 = ((var2 * (var3 + (int32_t)32768)) / 1024) + (int32_t)2097152;
  var2 = ((var4 * ((int32_t)_bme280_calib.dig_H2)) + 8192) / 16384;
  var3 = var5 * var2;
  var4 = ((var3 / 32768) * (var3 / 32768)) / 128;
  var5 = var3 - ((var4 * ((int32_t)_bme280_calib.dig_H1)) / 16);
  var5 = (var5 < 0 ? 0 : var5);
  var5 = (var5 > 419430400 ? 419430400 : var5);
  uint32_t H = (uint32_t)(var5 / 4096);

  return  (float)H / 1024.0;
}


/*!
 *   Calculates the altitude (in meters) from the specified atmospheric
 *   pressure (in hPa), and sea-level pressure (in hPa).
 *   @param  seaLevel      Sea-level pressure in hPa
 *   @returns the altitude value read from the device
 */
float Adafruit_BME280::readAltitude(float seaLevel) {
  // Equation taken from BMP180 datasheet (page 16):
  //  http://www.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf

  // Note that using the equation from wikipedia can give bad results
  // at high altitude. See this thread for more information:
  //  http://forums.adafruit.com/viewtopic.php?f=22&t=58064

  float atmospheric = readPressure() / 100.0F;
  return 44330.0 * (1.0 - pow(atmospheric / seaLevel, 0.1903));
}

/*!
 *   Calculates the pressure at sea level (in hPa) from the specified
 * altitude (in meters), and atmospheric pressure (in hPa).
 *   @param  altitude      Altitude in meters
 *   @param  atmospheric   Atmospheric pressure in hPa
 *   @returns the pressure at sea level (in hPa) from the specified altitude
 */
float Adafruit_BME280::seaLevelForAltitude(float altitude, float atmospheric) {
  // Equation taken from BMP180 datasheet (page 17):
  //  http://www.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf

  // Note that using the equation from wikipedia can give bad results
  // at high altitude. See this thread for more information:
  //  http://forums.adafruit.com/viewtopic.php?f=22&t=58064

  return atmospheric / pow(1.0 - (altitude / 44330.0), 5.255);
}

/*!
 *   Returns Sensor ID found by init() for diagnostics
 *   @returns Sensor ID 0x60 for BME280, 0x56, 0x57, 0x58 BMP280
 */
uint32_t Adafruit_BME280::sensorID(void) { return _sensorID; }

/*!
    @brief  Gets an Adafruit Unified Sensor object for the temp sensor component
    @return Adafruit_Sensor pointer to temperature sensor
 */
Adafruit_Sensor *Adafruit_BME280::getTemperatureSensor(void) {
  if (!temp_sensor) {
    temp_sensor = new Adafruit_BME280_Temp(this);
  }

  return temp_sensor;
}

/*!
    @brief  Gets an Adafruit Unified Sensor object for the pressure sensor
   component
    @return Adafruit_Sensor pointer to pressure sensor
 */
Adafruit_Sensor *Adafruit_BME280::getPressureSensor(void) {
  if (!pressure_sensor) {
    pressure_sensor = new Adafruit_BME280_Pressure(this);
  }
  return pressure_sensor;
}

/*!
    @brief  Gets an Adafruit Unified Sensor object for the humidity sensor
   component
    @return Adafruit_Sensor pointer to humidity sensor
 */
Adafruit_Sensor *Adafruit_BME280::getHumiditySensor(void) {
  if (!humidity_sensor) {
    humidity_sensor = new Adafruit_BME280_Humidity(this);
  }
  return humidity_sensor;
}

/**************************************************************************/
/*!
    @brief  Gets the sensor_t data for the BME280's temperature sensor
*/
/**************************************************************************/
void Adafruit_BME280_Temp::getSensor(sensor_t *sensor) {
  /* Clear the sensor_t object */
  memset(sensor, 0, sizeof(sensor_t));

  /* Insert the sensor name in the fixed length char array */
  strncpy(sensor->name, "BME280", sizeof(sensor->name) - 1);
  sensor->name[sizeof(sensor->name) - 1] = 0;
  sensor->version = 1;
  sensor->sensor_id = _sensorID;
  sensor->type = SENSOR_TYPE_AMBIENT_TEMPERATURE;
  sensor->min_delay = 0;
  sensor->min_value = -40.0; /* Temperature range -40 ~ +85 C  */
  sensor->max_value = +85.0;
  sensor->resolution = 0.01; /*  0.01 C */
}

/**************************************************************************/
/*!
    @brief  Gets the temperature as a standard sensor event
    @param  event Sensor event object that will be populated
    @returns True
*/
/**************************************************************************/
bool Adafruit_BME280_Temp::getEvent(sensors_event_t *event) {
  /* Clear the event */
  memset(event, 0, sizeof(sensors_event_t));

  event->version = sizeof(sensors_event_t);
  event->sensor_id = _sensorID;
  event->type = SENSOR_TYPE_AMBIENT_TEMPERATURE;
  event->timestamp = millis();
  event->temperature = _theBME280->readTemperature();
  return true;
}

/**************************************************************************/
/*!
    @brief  Gets the sensor_t data for the BME280's pressure sensor
*/
/**************************************************************************/
void Adafruit_BME280_Pressure::getSensor(sensor_t *sensor) {
  /* Clear the sensor_t object */
  memset(sensor, 0, sizeof(sensor_t));

  /* Insert the sensor name in the fixed length char array */
  strncpy(sensor->name, "BME280", sizeof(sensor->name) - 1);
  sensor->name[sizeof(sensor->name) - 1] = 0;
  sensor->version = 1;
  sensor->sensor_id = _sensorID;
  sensor->type = SENSOR_TYPE_PRESSURE;
  sensor->min_delay = 0;
  sensor->min_value = 300.0; /* 300 ~ 1100 hPa  */
  sensor->max_value = 1100.0;
  sensor->resolution = 0.012; /* 0.12 hPa relative */
}

/**************************************************************************/
/*!
    @brief  Gets the pressure as a standard sensor event
    @param  event Sensor event object that will be populated
    @returns True
*/
/**************************************************************************/
bool Adafruit_BME280_Pressure::getEvent(sensors_event_t *event) {
  /* Clear the event */
  memset(event, 0, sizeof(sensors_event_t));

  event->version = sizeof(sensors_event_t);
  event->sensor_id = _sensorID;
  event->type = SENSOR_TYPE_PRESSURE;
  event->timestamp = millis();
  event->pressure = _theBME280->readPressure() / 100; // convert Pa to hPa
  return true;
}

/**************************************************************************/
/*!
    @brief  Gets the sensor_t data for the BME280's humidity sensor
*/
/**************************************************************************/
void Adafruit_BME280_Humidity::getSensor(sensor_t *sensor) {
  /* Clear the sensor_t object */
  memset(sensor, 0, sizeof(sensor_t));

  /* Insert the sensor name in the fixed length char array */
  strncpy(sensor->name, "BME280", sizeof(sensor->name) - 1);
  sensor->name[sizeof(sensor->name) - 1] = 0;
  sensor->version = 1;
  sensor->sensor_id = _sensorID;
  sensor->type = SENSOR_TYPE_RELATIVE_HUMIDITY;
  sensor->min_delay = 0;
  sensor->min_value = 0;
  sensor->max_value = 100; /* 0 - 100 %  */
  sensor->resolution = 3;  /* 3% accuracy */
}

/**************************************************************************/
/*!
    @brief  Gets the humidity as a standard sensor event
    @param  event Sensor event object that will be populated
    @returns True
*/
/**************************************************************************/
bool Adafruit_BME280_Humidity::getEvent(sensors_event_t *event) {
  /* Clear the event */
  memset(event, 0, sizeof(sensors_event_t));

  event->version = sizeof(sensors_event_t);
  event->sensor_id = _sensorID;
  event->type = SENSOR_TYPE_RELATIVE_HUMIDITY;
  event->timestamp = millis();
  event->relative_humidity = _theBME280->readHumidity();
  return true;
}