//// **********************************************************************************************************
//// NEEDED TO COMMENT THIS WHOLE SKETCH OUT BECAUSE OF THE LCD LIBRARY IS CAUSING A CC BUILD FAIL
/// **********************************************************************************************************
//// GarageMote garage door controller base receiver sketch that works with Moteinos equipped with HopeRF RFM69W/RFM69HW
//// Can be adapted to use Moteinos using RFM12B
//// This is the sketch for the base, not the controller itself, and meant as another example on how to use a
//// Moteino as a gateway/base/receiver
//// 2014-07-14 (C) felix@lowpowerlab.com, http://www.LowPowerLab.com
//// **********************************************************************************************************
//// Creative Commons Attrib Share-Alike License
//// You are free to use/extend this code/library but please abide with the CCSA license:
//// http://creativecommons.org/licenses/by-sa/4.0/
//// **********************************************************************************
//
//#include <RFM69.h>         //get it here: http://github.com/lowpowerlab/rfm69
//#include <SPIFlash.h>      //get it here: http://github.com/lowpowerlab/spiflash
//#include <WirelessHEX69.h> //get it here: https://github.com/LowPowerLab/WirelessProgramming
//#include <SPI.h>           //comes with Arduino IDE (www.arduino.cc)
//#include "ST7036.h"        //get it from here: https://bitbucket.org/fmalpartida/st7036-display-driver/src/
//#include "LCD_C0220BiZ.h"  //get it from here: https://bitbucket.org/fmalpartida/st7036-display-driver/src/
//#include <Wire.h>          //comes with Arduino
//
////*****************************************************************************************************************************
//// ADJUST THE SETTINGS BELOW DEPENDING ON YOUR HARDWARE/SITUATION!
////*****************************************************************************************************************************
//#define NODEID          1
//#define NETWORKID     200
//#define FREQUENCY     RF69_915MHZ //Match this with the version of your Moteino! (others: RF69_433MHZ, RF69_868MHZ)
//#define ENCRYPTKEY    "sampleEncryptKey" //has to be same 16 characters/bytes on all nodes, not more not less!
//#define IS_RFM69HW    //uncomment only for RFM69HW! Leave out if you have RFM69W!
//#define LED             9
//#define FLASH_CS        8
//#define SERIAL_BAUD 115200
//#define SERIAL_EN     //comment out if you don't want any serial verbose output
//#define ACK_TIME       30  // # of ms to wait for an ack
//#define BACKLIGHTPIN    5 //3=R,5=G,6=B
////*****************************************************************************************************************************
//
//#ifdef SERIAL_EN
//  #define DEBUG(input)   {Serial.print(input); delay(1);}
//  #define DEBUGln(input) {Serial.println(input); delay(1);}
//#else
//  #define DEBUG(input);
//  #define DEBUGln(input);
//#endif
//
//RFM69 radio;
//SPIFlash flash(FLASH_CS, 0xEF30); //EF40 for 16mbit windbond chip
//
////initialize LCD
//ST7036 lcd = ST7036(2, 20, 0x78, BACKLIGHTPIN); //row count, column count, I2C addr, pin for backlight PWM
//byte battChar[8] = {0b00000,0b01110,0b11111,0b11111,0b11111,0b11111,0b11111,0};
//byte rssiChar[8] = {0b00000,0b00100,0b10101,0b01110,0b00100,0b00100,0b00100,0};
//
//void setup() {
//  Serial.begin(SERIAL_BAUD);
//  delay(10);
//  radio.initialize(FREQUENCY,NODEID,NETWORKID);
//#ifdef IS_RFM69HW
//  radio.setHighPower(); //uncomment only for RFM69HW!
//#endif
//  radio.encrypt(ENCRYPTKEY);
//  char buff[50];
//  sprintf(buff, "\nListening @ %dmhz...", FREQUENCY==RF69_433MHZ ? 433 : FREQUENCY==RF69_868MHZ ? 868 : 915);
//  DEBUGln(buff);
//  if (flash.initialize())
//  {
//    DEBUGln("SPI Flash Init OK!");
//  }
//  else
//    DEBUGln("SPI Flash Init FAIL! (is chip present?)");
//    
//  lcd.init();
//  lcd.setContrast(10);
//  lcd.clear();
//  lcd.load_custom_character(0, battChar);
//  lcd.load_custom_character(1, rssiChar);
//  lcd.setCursor(0,0);
//  lcd.print(buff);
//}
//
//byte ackCount=0;
//byte inputLen=0;
//char input[64];
//byte buff[61];
//char LO[20];
//char BAT[20];
//char temp[25];
//String inputstr;
//void loop() {
//  inputLen = readSerialLine(input, 10, 64, 10); //readSerialLine(char* input, char endOfLineChar=10, byte maxLength=64, uint16_t timeout=10);
//  inputstr = String(input);
//  inputstr.toUpperCase();
//  
//  if (inputLen > 0)
//  {
//    if (inputstr.equals("KEY?"))
//    {
//      DEBUG("ENCRYPTKEY:");
//      DEBUG(ENCRYPTKEY);
//    }
//    
//    byte targetId = inputstr.toInt(); //extract ID if any
//    byte colonIndex = inputstr.indexOf(":"); //find position of first colon
//    if (targetId > 0) inputstr = inputstr.substring(colonIndex+1); //trim "ID:" if any
//    if (targetId > 0 && targetId != NODEID && targetId != RF69_BROADCAST_ADDR && colonIndex>0 && colonIndex<4 && inputstr.length()>0)
//    {
//      
//      inputstr.getBytes(buff, 61);
//      //DEBUGln((char*)buff);
//      //DEBUGln(targetId);
//      //DEBUGln(colonIndex);
//      if (radio.sendWithRetry(targetId, buff, inputstr.length()))
//      {
//        DEBUGln("ACK:OK");
//      }
//      else
//        DEBUGln("ACK:NOK");
//    }
//  }
//
//  if (radio.receiveDone())
//  {
//    int rssi = radio.RSSI;
//    DEBUG('[');DEBUG(radio.SENDERID);DEBUG("] ");
//    if (radio.DATALEN > 0)
//    {
//      for (byte i = 0; i < radio.DATALEN; i++)
//        DEBUG((char)radio.DATA[i]);
//      DEBUG("   [RSSI:");DEBUG(rssi);DEBUG("]");
//    }
//
//    CheckForWirelessHEX(radio, flash, false); //non verbose DEBUG
//
//    if (radio.ACKRequested())
//    {
//      byte theNodeID = radio.SENDERID;
//      radio.sendACK();
//      DEBUG("[ACK-sent]");
//    }
//    DEBUGln();
//    Blink(LED,3);
//    
//    lcd.clear();
//    lcd.setCursor(0,0);
//
//    //if (radio.DATALEN < RF69_MAX_DATA_LEN) radio.DATA[radio.DATALEN]=0;
//    byte matches = sscanf((const char*)radio.DATA, "%s BAT:%s", LO, BAT);
//    if (matches==2)
//    {
//      lcd.print(LO);
//      lcd.setCursor(0,14);
//      lcd.print(char(0));
//      lcd.setCursor(0,15);
//      lcd.print(BAT);
//    }
//    else lcd.print((const char*)radio.DATA);
//    
//    lcd.setCursor(1,14);
//    lcd.print(char(1));
//    lcd.setCursor(1,16);
//    lcd.print(rssi);
//  }
//}
//
//void Blink(byte PIN, int DELAY_MS)
//{
//  pinMode(PIN, OUTPUT);
//  digitalWrite(PIN,HIGH);
//  delay(DELAY_MS);
//  digitalWrite(PIN,LOW);
//}
//
////readSerialLine already defined in WirelessHEX69
//// reads a line feed (\n) terminated line from the serial stream
//// returns # of bytes read, up to 255
//// timeout in ms, will timeout and return after so long
////byte readSerialLine(char* input, char endOfLineChar=10, byte maxLength=64, uint16_t timeout=10);
////byte readSerialLine(char* input, char endOfLineChar, byte maxLength, uint16_t timeout)
////{
////  byte inputLen = 0;
////  Serial.setTimeout(timeout);
////  inputLen = Serial.readBytesUntil(endOfLineChar, input, maxLength);
////  input[inputLen]=0;//null-terminate it
////  Serial.setTimeout(0);
////  //Serial.println();
////  return inputLen;
////}