Cansat
/
RFM69_LowPowerLab
2
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Motion &WShield fixes

This commit is contained in:
Felix Rusu 2018-05-01 17:51:27 -04:00
parent c7bddb1f78
commit cb74f772fe
2 changed files with 17 additions and 16 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

17
Examples/MotionMote/MotionMote.ino
View File

@ -1,10 +1,10 @@
// Sample RFM69 sender/node sketch for the MotionMote
// http://lowpowerlab.com/motionmote
// https://lowpowerlab.com/guide/motionmote/
// PIR motion sensor connected to D3 (INT1)
// When RISE happens on D3, the sketch transmits a "MOTION" msg to receiver Moteino and goes back to sleep
// In sleep mode, Moteino + PIR motion sensor use about ~60uA
// With Panasonic PIRs it's possible to use only around ~9uA, see guide link above for details
// IMPORTANT: adjust the settings in the configuration section below !!!
// **********************************************************************************
// Copyright Felix Rusu of LowPowerLab.com, 2018
// RFM69 library and sample code by Felix Rusu - lowpowerlab.com/contact
@ -41,9 +41,9 @@
//****************************************************************************************************************
//**** IMPORTANT RADIO SETTINGS - YOU MUST CHANGE/CONFIGURE TO MATCH YOUR HARDWARE TRANSCEIVER CONFIGURATION! ****
//****************************************************************************************************************
#define GATEWAYID 1
#define NODEID 88 //unique for each node on same network
#define NETWORKID 100 //the same on all nodes that talk to each other
#define GATEWAYID 1
//Match frequency to the hardware version of the radio on your Moteino (uncomment one):
//#define FREQUENCY RF69_433MHZ
//#define FREQUENCY RF69_868MHZ
@ -137,14 +137,13 @@ void setup() {
if (flash.initialize()) flash.sleep(); //if Moteino has FLASH-MEM, make sure it sleeps
#ifdef ENABLE_BME280
Wire.begin();
Wire.setClock(400000); //Increase to fast I2C speed!
//initialize weather shield BME280 sensor
bme280.setI2CAddress(0x77); //0x76,0x77 is valid.
bme280.beginI2C();
bme280.setMode(MODE_SLEEP); //MODE_SLEEP, MODE_FORCED, MODE_NORMAL is valid. See 3.3
bme280.setMode(MODE_FORCED); //MODE_SLEEP, MODE_FORCED, MODE_NORMAL is valid. See 3.3
bme280.setStandbyTime(0); //0 to 7 valid. Time between readings. See table 27.
bme280.setFilter(0); //0 to 4 is valid. Filter coefficient. See 3.4.4
bme280.setTempOverSample(1); //0 to 16 are valid. 0 disables temp sensing. See table 24.
@ -153,6 +152,7 @@ void setup() {
P = bme280.readFloatPressure() * 0.0002953; //read Pa and convert to inHg
F = bme280.readTempF();
H = bme280.readFloatHumidity();
bme280.setMode(MODE_SLEEP);
#endif
}
@ -181,7 +181,7 @@ void loop() {
P = bme280.readFloatPressure() * 0.0002953; //read Pa and convert to inHg
F = bme280.readTempF();
H = bme280.readFloatHumidity();
bme280.setMode(MODE_SLEEP);
dtostrf(F, 3,2, Fstr);
dtostrf(H, 3,2, Hstr);
dtostrf(P, 3,2, Pstr);
@ -215,12 +215,11 @@ void loop() {
P = bme280.readFloatPressure() * 0.0002953; //read Pa and convert to inHg
F = bme280.readTempF();
H = bme280.readFloatHumidity();
bme280.setMode(MODE_SLEEP);
dtostrf(F, 3,2, Fstr);
dtostrf(H, 3,2, Hstr);
dtostrf(P, 3,2, Pstr);
sprintf(sendBuf, "MOTION BAT:%sv F:%s H:%s P:%s", BATstr, Fstr, Hstr, Pstr);
sprintf(sendBuf, "BAT:%sv F:%s H:%s P:%s", BATstr, Fstr, Hstr, Pstr);
#else
sprintf(sendBuf, "BAT:%sv", BATstr);
#endif

6
Examples/WeatherNode/WeatherNode.ino
View File

@ -2,7 +2,7 @@
// WeatherShield R2 (BME280 sensor) sameple sketch that works with Moteinos equipped with RFM69W/RFM69HW
// It sends periodic weather readings (temp, hum, atm pressure) from WeatherShield to the base node Moteino
// For use with MoteinoMEGA you will have to revisit the pin definitions defined below
// http://www.LowPowerLab.com/WeatherShield
// https://lowpowerlab.com/guide/weathershield/
// Example setup (with R1): http://lowpowerlab.com/blog/2015/07/24/attic-fan-cooling-tests/
// **********************************************************************************
// Copyright Felix Rusu 2018, http://www.LowPowerLab.com/contact
@ -137,7 +137,7 @@ void setup(void)
//initialize weather shield BME280 sensor
bme280.setI2CAddress(0x77); //0x76,0x77 is valid.
bme280.beginI2C();
bme280.setMode(MODE_SLEEP); //MODE_SLEEP, MODE_FORCED, MODE_NORMAL is valid. See 3.3
bme280.setMode(MODE_FORCED); //MODE_SLEEP, MODE_FORCED, MODE_NORMAL is valid. See 3.3
bme280.setStandbyTime(0); //0 to 7 valid. Time between readings. See table 27.
bme280.setFilter(0); //0 to 4 is valid. Filter coefficient. See 3.4.4
bme280.setTempOverSample(1); //0 to 16 are valid. 0 disables temp sensing. See table 24.
@ -146,6 +146,7 @@ void setup(void)
P = bme280.readFloatPressure() * 0.0002953; //read Pa and convert to inHg
F = bme280.readTempF();
H = bme280.readFloatHumidity();
bme280.setMode(MODE_SLEEP);
radio.sendWithRetry(GATEWAYID, "START", 6);
Blink(LED, 100);Blink(LED, 100);Blink(LED, 100);
@ -189,6 +190,7 @@ void loop()
P = bme280.readFloatPressure() * 0.0002953; //read Pa and convert to inHg
F = bme280.readTempF();
H = bme280.readFloatHumidity();
bme280.setMode(MODE_SLEEP);
dtostrf(F, 3,2, Fstr);
dtostrf(H, 3,2, Hstr);